In order to change your air conditioner sensor, you will need a few tools and materials. You will need a new sensor, a screwdriver, and a pair of pliers. You may also need a drill, depending on how your old sensor is attached.
How to change inside air conditioner sensor on 2013 smart passion
A screwdriver is a tool, manual or powered, for screwing and unscrewing (inserting and removing) screws. A typical simple screwdriver has a handle and a shaft, ending in a tip the user inserts into the screw head before turning the handle.
The first documented screws were used in Europe in the 15th century. They were used in clocks and guns, but it was not until the 17th century that they began to be widely used in carpentry. An early record of the screw pitch (and hence size) comes from Leonardo da Vinci’s notebooks showing that he designed a helicopter with screws 8 times as long as they were wide with pitch 4 times the diameter. In Moxon’s Mechanick Exercises (1678), Joseph Moxon actually gives formula for making calculating screws of any size or pitch.
New sensor
You will need a few tools and materials before you can change your air conditioner sensor. The most important tool you will need is a screwdriver. You will also need a new sensor, which you can purchase at your local hardware store. Finally, you will need a rag or some other type of cloth to clean the old sensor before you install the new one.
Steps
In order to change your air conditioner sensor, you will need a few tools and materials. You will need a ratchet, a Phillips head screwdriver, a Torx head screwdriver, and a flat head screwdriver. You will also need a new air conditioner sensor. You can purchase this from your local auto parts store.
Turn off power to air conditioner
Before replacing an air conditioner sensor, it is important to turn off power to the air conditioner. This can be done by flipping the circuit breaker to the “off” position. For safety, it is also a good idea to unplug the air conditioner from the wall outlet.
Remove front panel of air conditioner
In order to remove the front panel of your air conditioner, follow these steps:
-Locate the two screws at the top of the air conditioner’s front panel.
-Using a screwdriver, remove the screws.
-Carefully pull the front panel away from the rest of the unit.
Locate old sensor
The first step is to locate the old sensor. The sensor is usually located near the air conditioner unit, on the wall or on the ceiling. Once you have found the sensor, unplug it from the power source.
Remove old sensor
1. Turn off your air conditioner.
2. Locate the old sensor. It will be mounted on or near the air conditioner’s evaporator coils.
3. Disconnect the old sensor from the wiring harness.
4. Remove the old sensor from its mount.
5. Clean the area around the new sensor’s mount.
6. Install the new sensor in the same location as the old one.
7. Connect the new sensor to the wiring harness.
8. Turn on your air conditioner and test the new sensor to make sure it is working properly.”
Install new sensor
1. To begin, you will need toShut off the power to the AC unit.
2. Next, remove the panel to access the current sensor.
3. Carefully disconnect the old sensor, and remove it from the AC unit.
4. Take your new sensor, and connect it to the AC unit in the place of the old one.
5. Be sure that it is snug and secure before moving on to the next step
6. Finally, put the panel back on, turn on the power to the AC unit, and check that it is working properly.
Replace front panel
To replace the front panel, follow these steps:
1. Unplug the air conditioner and remove the screws that hold the front panel in place.
2. Carefully remove the front panel and set it aside.
3. Disconnect the wires from the old sensor and remove it from the air conditioner.
4. Install the new sensor in the air conditioner and reconnect the wires.
5. Replace the front panel and screw it in place.
6. Plug in the air conditioner and turn it on
Turn power back on
After the new sensor is in place, screw the panels back onto the unit. Reattach any duct work or wiring that was removed to access the sensor. Finally, turn the power back on to the unit and test it out to make sure that the new sensor is working properly.